Skip to content
TACHYONS ENERGYPRIVATE LIMITED

HT & LT ELECTRICAL WORKS

HT & LT Electrical Contractor for Industrial and Utility Installations

Tachyons Energy Private Limited is an HT and LT electrical contractor that installs, tests and commissions high-tension (11kV and 33kV) and low-tension (415V) power systems for industries, commercial buildings and utility intakes. The scope covers HT switchgear and ring main units, distribution transformers, metering cubicles, LT panels and distribution, cabling and earthing, through to the documentation submitted for State Electrical Inspectorate approval before energisation. The company is based in Kerala, India.

  • 11kV
  • 33kV
  • LT 415V

What HT and LT electrical work means

HT (high tension) refers to systems above 1kV; for most industrial and commercial consumers in India this means an 11kV or 33kV supply from the utility. LT (low tension) covers systems up to 1kV, typically 415V three-phase and 240V single-phase, which is the level at which most machines, lighting and building services run. An HT consumer takes supply at 11kV or 33kV, steps it down through its own transformer and distributes power at LT inside the premises, so both sides have to be engineered, installed and tested as one system.

HT works: 11kV and 33kV

On the HT side, Tachyons Energy installs the equipment between the utility supply point and the transformer secondary. The work follows the approved single-line diagram, the utility (KSEB) requirements for HT consumers and the applicable IEC / IS standards.

  • Indoor VCB panels and HT switchboards: erection, bus coupling and alignment
  • Ring main units (RMUs) for loop-in / loop-out distribution and transformer feeders
  • Distribution transformers: placement, HV and LV terminations, oil checks and pre-commissioning tests
  • HT metering cubicles with CT / PT, prepared for utility metering and sealing
  • HT XLPE cable laying and indoor / outdoor terminations
  • Protection relay wiring, settings loading and secondary injection testing
  • Surge arresters and interlocks between switchgear and transformer

LT works: 415V distribution

From the transformer LV side, power is distributed at 415V through main and sub-distribution panels to loads. LT work is sized and laid out so that feeders, protection and cable runs match the load schedule and can be safely isolated for maintenance.

  • Main LT panels (PCC) with ACB incomers and bus couplers
  • Motor control centres (MCC) and sub-distribution boards with MCCB / MCB feeders
  • Automatic power factor correction (APFC) panel installation
  • LT power and control cabling on trays, in trenches or through ducts
  • Transformer-to-panel connections by cable or busduct
  • Feeder labelling, schedules and discrimination checks

Earthing, testing and statutory approval

Every installation is earthed and tested before any approval is sought. Neutral and body earthing for transformers, switchgear and panels is installed to the earthing design and measured, and the complete installation is documented for inspection.

  • Pipe, plate or chemical earth electrodes and earth-pit construction to the design
  • Equipment, neutral and lightning-arrester earthing with resistance measurement
  • Insulation resistance tests of cables, switchgear and transformers
  • Relay, CT ratio and polarity, and transformer pre-commissioning tests
  • Drawings, test reports and documentation for State Electrical Inspectorate approval
  • Support during the inspection and the utility supply release

HOW THE WORK RUNS

How we deliver ht & lt electrical works

  1. 01

    Site survey and load review

    Visit to the premises to review the supply point, connected load, existing equipment, space for the substation room or yard, and cable routes.

  2. 02

    Single-line diagram and drawings

    Preparation or review of the single-line diagram, equipment layout, earthing layout and cable schedule, aligned with utility and inspectorate requirements.

  3. 03

    Equipment receipt and installation

    Inspection of HT switchgear, RMUs, transformers and LT panels on arrival, followed by erection, cabling, terminations and earthing.

  4. 04

    Testing and pre-commissioning

    Insulation resistance, earth resistance, transformer tests, relay secondary injection and interlock checks, with every result recorded.

  5. 05

    Inspectorate approval

    Submission of drawings and test reports to the State Electrical Inspectorate and support during the site inspection.

  6. 06

    Energisation and handover

    Charging of the installation in coordination with the utility, on-load checks of protection and metering, and handover of as-built drawings and test records.

QUESTIONS & ANSWERS

HT & LT Electrical Works: common questions

Straight answers to what clients ask us most before a project starts.

What is the difference between HT and LT electrical work?

HT (high tension) work covers equipment operating above 1kV, such as 11kV and 33kV switchgear, ring main units, HT cables and the primary side of transformers. LT (low tension) work covers systems up to 1kV, typically 415V three-phase distribution panels, feeders and cabling to loads. HT work generally needs higher-rated equipment, specialised cable jointing and statutory inspection before charging.

Who approves an HT installation in Kerala?

In Kerala, a new or modified HT installation is inspected by the State Electrical Inspectorate against the CEA safety regulations before it can be energised. The utility, KSEB, also has its own requirements for metering and supply connection. The contractor prepares the drawings and test reports for submission and supports the inspection on site.

When does a factory or building need an HT connection?

An HT connection is generally needed once the connected load or contract demand exceeds the limit the utility allows on an LT supply. The exact threshold is set by the utility and the state electricity regulatory commission, so it should be confirmed with KSEB or the relevant distribution company for the site. An HT consumer then owns and maintains its own transformer and HT switchgear.

What is an RMU and where is it used?

A ring main unit (RMU) is a compact, enclosed set of HT switchgear, usually combining load-break switches and a circuit breaker or fuse-switch for a transformer feeder. RMUs are used on 11kV distribution networks so that a cable ring can be fed from either side and a faulty section isolated. They are common at industrial intakes, commercial buildings and secondary substations where space is limited.

What tests are done before an HT installation is charged?

Typical tests include insulation resistance of cables, switchgear and transformer windings, transformer ratio and winding resistance, oil breakdown voltage, CT ratio and polarity, relay secondary injection, interlock checks and earth resistance measurement. HT cables are also tested after termination. The results form part of the documentation submitted for inspectorate approval.

Does Tachyons Energy handle both HT and LT work on the same project?

Yes. Tachyons Energy carries out the HT side from the utility supply point through switchgear and transformer, and the LT side through main panels, distribution boards, cabling and earthing. Handling both under one scope keeps protection settings, cable sizing and earthing consistent across the installation.